5.9 KiB
Powercore V2.0
1. Overview of the Project
The Powercore V2.0 is an open-source wire EDM (electrical discharge machining) power supply developed by Rack Robotics. It aims to provide a cost-effective and easily replicable solution for wire EDM enthusiasts and professionals. The project includes detailed electrical schematics, firmware, and CAD models. This EDM power supply (spark generator) is intedned to be used on custom wire EDM and plunge EDM machines.
Hardware Specifications
| Powercore V2.0 Specification | Value |
|---|---|
| Typical Input Power | 200 Watts |
| Input Voltage | 90-264 VAC |
| Input Frequency | 47-63 Hz |
| Output Voltage | 65 VDC |
| Power Efficiency | Up to 90% |
| PSU Enable Port Voltage Input | 5-36 V |
| Physical Dimensions (XYZ) | 97 x 224 x 79.5 (mm) |
Features
- Firmare optimized for stable wire EDM opperation
- Up to 180 Watts EDM Power Output (Output Port)
- Up to 18 mJ per EDM spark
- Up to 10 kHz Maximum EDM Pulse Frequency
- Dual-core RP2040 Microcontroller up to 133 MHz (USB Port)
- Real-Time Current Sensing Telemetry (AMP Port)
- Real-Time Spark Ignition Telemetry (ALRT Port)
- External PSU Enable Safety Feature
FAQ
Can this cut X material?
EDM can errode any conductive material. The rate of EDM (Electrical Discharge Machining) machining, also known as spark erosion, is significantly influenced by the thickness, melting point, and density of the material being worked on. Thicker materials generally require more time to erode due to the increased volume that must be removed. Materials with a higher melting point also slow down the machining rate as more energy is required to melt and vaporize the material at the spark point. Additionally, denser materials resist erosion more effectively, requiring more discharge energy to achieve the same material removal rate as less dense materials.
| Material | Example Feedrate |
|---|---|
| 3 mm Aluminum | 10 - 28 mm/min |
| 19 mm Aluminum | 1.6 - 4.4 mm/min |
| 4.75 mm Aluminum | 6 - 17 mm/min |
Can the Powercore V2.0 be used for sinker/plunge EDM?
Yes. Gap control is highly recommended for sinker/plunge applications. In plunge/sink EDM, gap control is critical for maintaining machining stability. The gap, or spark gap, is the small space between the electrode and the workpiece. Proper gap control ensures consistent sparking conditions, preventing short circuits and arcing that can damage the workpiece and electrode. It also aids in efficient debris removal, cooling, and flushing of the dielectric fluid, which are essential for maintaining a smooth surface finish and achieving high-accuracy machining. Without precise gap control, the machining process can become unstable, leading to poor-quality results and increased wear on the electrodes. The Powercore V2.0 has a current sense and short alert output port to assist the user in thier implementation.
2. Operation of the Powercore
POWER Port
The Powercore V2.0 outputs EDM waveforms through an 8-position Molex Micro-Fit 3.0 connector. The included output cable is 1 meter long and rated for 30 cycles. This cable consists of four twisted pairs to significantly reduce electromagnetic emissions. For more information about twisted wires and their benefits, refer to the best practices section.
ALRT Port
The Powercore V2.0 provides digital telemetry on the spark ignition rate via the ALRT port. The spark ignition rate, defined as the ratio of 'observed discharges' to 'possible discharges'. The spark ignition rate is a key indicator of feedrate efficiency. A low rate suggests the feedrate can be increased, while a high rate indicates an excessive feedrate or a short circuit. Telemetry is reported as a PWM duty cycle, which can be read by a control board or microcontroller. This port enables closed-loop feedrate control, ensuring optimal material removal. An ignition rate of approximately 80% has been observed to be optimal.
AMP Port
The Powercore V2.0 provides analog telemetry via the on-board current sensor (U17A, LMV358AIDGKR, output shunt). It is mapped to between 0V and 3.3V, at a rate of 12 mV/A. This may be used for closed-loop feedback control and debugging.
EN Port
The Powercore V2.0 features an "enable port" that ensures safety by requiring activation before the device outputs EDM waveforms. When the Powercore is plugged in, it remains inactive until the enable port receives a DC voltage between 5V and 36V. This port draws minimal current. The enable port can be connected to GPIO, motor, heater, or LED ports on a 3D printer or CNC control board, or controlled manually with a switch. To prevent damage, avoid disconnecting the main AC power while the enable port is active.
USB Port
A type-C USB port provides communication with the on-board RP2040 micronctroller and flash memory. Pressing the reset button (the pin-hole located between the ‘AMP’ and ‘EN’ ports) during power-up initiates the USB bootloader mode, allowing access to the flash memory. When the reset button is held down while powering up, the RP2040 enters a special state where it presents itself as a mass storage device to a connected computer. This enables users to drag and drop firmware files directly into the flash memory, facilitating easy updates and modifications without needing additional programming tools or interfaces.