clean up of files

KAMP_Settings.cfg

@@ -1,36 +0,0 @@
-# Below you can include specific configuration files depending on what you want KAMP to do:
-
-[include ./KAMP/Adaptive_Meshing.cfg]       # Include to enable adaptive meshing configuration.
-[include ./KAMP/Line_Purge.cfg]             # Include to enable adaptive line purging configuration.
-[include ./KAMP/Voron_Purge.cfg]            # Include to enable adaptive Voron logo purging configuration.
-[include ./KAMP/Smart_Park.cfg]             # Include to enable the Smart Park function, which parks the printhead near the print area for final heating.
-
-[gcode_macro _KAMP_Settings]
-description: This macro contains all adjustable settings for KAMP 
-
-# The following variables are settings for KAMP as a whole.
-variable_verbose_enable: True               # Set to True to enable KAMP information output when running. This is useful for debugging.
-
-# The following variables are for adjusting adaptive mesh settings for KAMP.
-variable_mesh_margin: 10                     # Expands the mesh size in millimeters if desired. Leave at 0 to disable.
-variable_fuzz_amount: 3                     # Slightly randomizes mesh points to spread out wear from nozzle-based probes. Leave at 0 to disable.
-
-# The following variables are for those with a dockable probe like Klicky, Euclid, etc.                 # ----------------  Attach Macro | Detach Macro
-variable_probe_dock_enable: False           # Set to True to enable the usage of a dockable probe.      # ---------------------------------------------
-variable_attach_macro: 'Attach_Probe'       # The macro that is used to attach the probe.               # Klicky Probe:   'Attach_Probe' | 'Dock_Probe'
-variable_detach_macro: 'Dock_Probe'         # The macro that is used to store the probe.                # Euclid Probe:   'Deploy_Probe' | 'Stow_Probe'
-                                                                                                        # Legacy Gcode:   'M401'         | 'M402'
-
-# The following variables are for adjusting adaptive purge settings for KAMP.
-variable_purge_height: 0.8                  # Z position of nozzle during purge, default is 0.8.
-variable_tip_distance: 1                    # Distance between tip of filament and nozzle before purge. Should be similar to PRINT_END final retract amount.
-variable_purge_margin: 10                   # Distance the purge will be in front of the print area, default is 10.
-variable_purge_amount: 30                   # Amount of filament to be purged prior to printing.
-variable_flow_rate: 12                      # Flow rate of purge in mm3/s. Default is 12.
-
-# The following variables are for adjusting the Smart Park feature for KAMP, which will park the printhead near the print area at a specified height.
-variable_smart_park_height: 10              # Z position for Smart Park, default is 10.
-
-gcode: # Gcode section left intentionally blank. Do not disturb.
-
-    {action_respond_info(" Running the KAMP_Settings macro does nothing, it is only used for storing KAMP settings. ")}

hardware/hardware.cfg

@@ -2,4 +2,3 @@
 [include steppers.cfg]
 [include manta.cfg]
 [include nitehawk.cfg]
-#[include nh-36.cfg]

hardware/nh-36.cfg

@@ -1,14 +0,0 @@
-
-[mcu nhk]
-##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
-##--------------------------------------------------------------------
-serial: 4E473531310A2450
-restart_method: command
-
-#####################################################################
-# 	Probe
-#####################################################################
-## Probe Port
-[probe]
-pin: nhk:gpio10
-z_offset: -0.890

printer-20240827_221828.cfg

@@ -1,15 +0,0 @@
-#[include print_area_bed_mesh.cfg]
-[include mainsail.cfg]
-[include hardware/hardware.cfg]
-[include misc/misc.cfg]
-[include macros/macros.cfg]
-
-[printer]
-max_velocity: 600
-max_accel: 6500
-kinematics: corexy
-max_z_velocity: 30 			#Max 15 for 12V TMC Drivers, can increase for 24V
-max_z_accel: 350
-square_corner_velocity: 5.0
-
-[exclude_object]

printer-20240901_090049.cfg

@@ -1,40 +0,0 @@
-#[include print_area_bed_mesh.cfg]
-[include mainsail.cfg]
-[include hardware/hardware.cfg]
-[include misc/misc.cfg]
-[include macros/macros.cfg]
-[include config/config.cfg]
-[include KAMP_Settings.cfg]
-
-[printer]
-max_velocity: 600
-max_accel: 6500
-kinematics: corexy
-max_z_velocity: 30 			#Max 15 for 12V TMC Drivers, can increase for 24V
-max_z_accel: 350
-square_corner_velocity: 5.0
-
-[exclude_object]
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	  0.129938, 0.077438, 0.072438, 0.064938, 0.079938, 0.084938, 0.092438
-#*# 	  0.074938, 0.042438, 0.032438, 0.029938, 0.032438, 0.059938, 0.079938
-#*# 	  0.024938, 0.012438, -0.015062, -0.007562, -0.000062, 0.022438, 0.032438
-#*# 	  0.014938, -0.000062, -0.015062, -0.020062, 0.007438, 0.027438, 0.047438
-#*# 	  0.044938, 0.029938, -0.012562, -0.002562, 0.009938, 0.024938, 0.039938
-#*# 	  0.089938, 0.049938, 0.012438, 0.019938, 0.029938, 0.032438, 0.064938
-#*# 	  0.152438, 0.109938, 0.074938, 0.069938, 0.069938, 0.069938, 0.079938
-#*# x_count = 7
-#*# y_count = 7
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 20.0
-#*# max_x = 320.0
-#*# min_y = 20.0
-#*# max_y = 320.0