152 lines
4.1 KiB
INI
152 lines
4.1 KiB
INI
[temperature_sensor MCU]
|
|
sensor_type: temperature_mcu
|
|
|
|
[temperature_sensor SoC]
|
|
sensor_type: temperature_host
|
|
|
|
[temperature_sensor chamber]
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PB0
|
|
min_temp: 0
|
|
max_temp: 100
|
|
gcode_id: chamber
|
|
pullup_resistor: 2200
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
|
|
[heater_bed]
|
|
## SSR Pin - HE1
|
|
heater_pin: PA1
|
|
## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types.
|
|
## Use "Generic 3950" for NTC 100k 3950 thermistors
|
|
#sensor_type:
|
|
sensor_pin: PB1
|
|
## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink.
|
|
## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power"
|
|
## If max_power is greater than 1.0, use 1.0
|
|
sensor_type: Generic 3950
|
|
max_power: 0.92
|
|
min_temp: 0
|
|
max_temp: 125
|
|
control: pid
|
|
pid_kp: 56.391
|
|
pid_ki: 1.843
|
|
pid_kd: 431.393
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[multi_pin ebay_fans_pin]
|
|
pins: PF7, PF9, PF6, PF8
|
|
|
|
[temperature_fan ebay_fans]
|
|
# Print Cooling Fan - CNC_FAN0
|
|
pin: multi_pin:ebay_fans_pin
|
|
hardware_pwm: false
|
|
control: watermark
|
|
max_delta: 5
|
|
sensor_type: temperature_host
|
|
min_temp: 15
|
|
max_temp: 80
|
|
target_temp: 50
|
|
max_power: 0.5
|
|
shutdown_speed: 0
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
[safe_z_home]
|
|
home_xy_position:175,175
|
|
speed:200
|
|
z_hop:10
|
|
|
|
[quad_gantry_level]
|
|
## Gantry Corners for 350mm Build
|
|
## Uncomment for 350mm build
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
#--------------------------------------------------------------------
|
|
speed: 600
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.025
|
|
max_adjust: 10
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PE7, EXP1_2=PG1,
|
|
EXP1_3=PG0, EXP1_4=PF15,
|
|
EXP1_5=PF14, EXP1_6=PF13, # Slot in the socket on this side
|
|
EXP1_7=PF12, EXP1_8=PF11,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PE13, EXP2_2=PE12,
|
|
EXP2_3=PE15, EXP2_4=PE11,
|
|
EXP2_5=PE10, EXP2_6=PE14, # Slot in the socket on this side
|
|
EXP2_7=PE8, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<NC>
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
[gcode_macro G32]
|
|
gcode:
|
|
BED_MESH_CLEAR
|
|
G28
|
|
QUAD_GANTRY_LEVEL
|
|
G28
|
|
## Uncomment for for your size printer:
|
|
#--------------------------------------------------------------------
|
|
## Uncomment for 250mm build
|
|
#G0 X125 Y125 Z30 F3600
|
|
|
|
## Uncomment for 300 build
|
|
#G0 X150 Y150 Z30 F3600
|
|
|
|
## Uncomment for 350mm build
|
|
#G0 X175 Y175 Z30 F3600
|
|
#--------------------------------------------------------------------
|
|
|
|
[gcode_macro PRINT_END]
|
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=STATE_PRINT_END
|
|
|
|
M400 ; wait for buffer to clear
|
|
G92 E0 ; zero the extruder
|
|
G1 E-10.0 F3600 ; retract filament
|
|
|
|
G91 ; relative positioning
|
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
|
TURN_OFF_HEATERS
|
|
M107 ; turn off fan
|
|
G1 Z2 F3000 ; move nozzle up 2mm
|
|
G90 ; absolute positioning
|
|
G0 X125 Y250 F3600 ; park nozzle at rear
|
|
BED_MESH_CLEAR
|
|
|
|
# The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE
|
|
# command pair is to restore the printer's coordinate system
|
|
# and speed settings since the commands above change them.
|
|
# However, to prevent any accidental, unintentional toolhead
|
|
# moves when restoring the state, explicitly set MOVE=0.
|
|
RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0
|