No modern driver pays attention to this. Presumably there existed
hardware once where you couldn't just read the right values out of the
CRTC.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Adam Jackson <ajax@redhat.com>
When the X server is compiled with --prefix set to something other than /usr,
then it ends up with a nonstandard sysconfigdir in its .pc file. This causes
various other components to install their xorg.conf.d snippets there.
However, the X server first looks for /usr/share/X11/xorg.conf.d before looking
in sysconfigdir. That means that if the system administrator installed anything
that created that path, the user's custom sysconfigdir is not searched.
Rather than doing that, just look in the configured sysconfdir and nowhere else.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Reviewed-by: Julien Cristau <jcristau@debian.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
To make X -configure work properly, the output of fixup_video_driver_list()
should be in order of preference. Otherwise, the config file may use
the incorrect driver for some devices.
In particular, the drivers that work for all (or many) devices need to be
last in the list. Since the modesetting driver works for many devices,
it needs to be considered a fallback driver.
Signed-off-by: Søren Sandmann <ssp@redhat.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This patch fixes some compile warnings that arise after
commit 7070ebeeba
(xfree86: add new key MatchSeat to xorg.conf sections "Device", "Screen", and "ServerLayout")
available at git repository
git://people.freedesktop.org/~whot/xserver for-keith
Signed-off-by: Keith Packard <keithp@keithp.com>
This patch introduces a new key MatchSeat in xorg.conf (also applies to
any .conf file in xorg.conf.d). It will allow targeting a given
"Device", "Screen", and/or "ServerLayout" section to a particular
seat only (specified by option "-seat" in X server command line),
so that other seats won't be affected.
Without this patch, one needs to write a separate xorg.conf.custom
file and pass it to X server via "-config" option, if one wants that
these settings only apply for the right seat. However, in some cases,
this solution is undesirable or even impossible (e.g. when using GDM,
which doesn't allow X server command line customization).
Example file (/etc/X11/xorg.conf.d/seat1.conf), which would be ignored
by X server unless it was started with "-seat seat1" option:
Section "Device"
Identifier "card0"
Driver "nvidia"
Option "NoLogo" "True"
MatchSeat "seat1"
EndSection
Signed-off-by: Oleg Samarin <osamarin68@gmail.com>
Signed-off-by: Laércio de Sousa <lbsousajr@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Just forcing everything to const char* is not helpful, compiler warnings are
supposed to warn about broken code. Forcing everything to const when it
clearly isn't less than ideal.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This lets us stop using the 'pointer' typedef in Xdefs.h as 'pointer'
is used throughout the X server for other things, and having duplicate
names generates compiler warnings.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
defaultFontPath is now a const char * so that it can be initialized
from a string constant. This patch kludges around that by inserting
suitable casts to eliminate warnings. Fixing this 'correctly' would
involve inserting some new variables and conditionals to use them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
On UEFI machines you'd prefer fbdev to grab efifb instead of vesa trying
to initialize and failing in a way we can't unwind from. On BIOS
machines this is harmless: either there is an fbdev driver and it'll
probably be more capable, or there's not and vesa will kick in anyway.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Adam Jackson <ajax@redhat.com>
This removes a large number of redundant declaration warnings.
Signed-off-by: Jeremy White <jwhite@codeweavers.com>
Reviewed-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Instead of keeping a tiny amount of code in an external module, just man
up and build it into the core server.
v2: Fix test/Makefile.am to only link libdri2.la if DRI2 is set
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Rather than building the tiny amount of code required for XFree86-DRI as
an external module, build it in if it's enabled at configure time.
v2: Fix test/Makefile.am to only link libdri.la if DRI is set
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
fixup for DRI1 move
Signed-off-by: Keith Packard <keithp@keithp.com>
extmod was originally a big pointless module. Now it's an empty,
pointless module. This commit makes it unexist.
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Rather than languishing in its own special module, move RECORD into the
core server.
Signed-off-by: Tomas Carnecky <tom@dbservice.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
If DBE support is compiled in the server, just man up and build it into
the server, rather than having it as an external module.
Signed-off-by: Tomas Carnecky <tom@dbservice.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
This option is to stop the X server adding non-primary devices as
gpu screens.
v2: fix per Keith's suggestion.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
*dev is the condition of the while loop we're in, reset to NULL after
freeing
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cygwin doesn't have ELF rpath capabilities, so these libraries need
to be loaded before the drivers (namely dummy and nested) which
depend on their symbols.
Signed-off-by: Yaakov Selkowitz <yselkowitz@users.sourceforge.net>
Reviewed-by: Jon TURNEY <jon.turney@dronecode.org.uk>
Reviewed-by: Jeremy Huddleston <jeremyhu@apple.com>
This is strictly the application of the script 'x-indent-all.sh'
from util/modular. Compared to the patch that Daniel posted in
January, I've added a few indent flags:
-bap
-psl
-T PrivatePtr
-T pmWait
-T _XFUNCPROTOBEGIN
-T _XFUNCPROTOEND
-T _X_EXPORT
The typedefs were needed to make the output of sdksyms.sh match the
previous output, otherwise, the code is formatted badly enough that
sdksyms.sh generates incorrect output.
The generated code was compared with the previous version and found to
be essentially identical -- "assert" line numbers and BUILD_TIME were
the only differences found.
The comparison was done with this script:
dir1=$1
dir2=$2
for dir in $dir1 $dir2; do
(cd $dir && find . -name '*.o' | while read file; do
dir=`dirname $file`
base=`basename $file .o`
dump=$dir/$base.dump
objdump -d $file > $dump
done)
done
find $dir1 -name '*.dump' | while read dump; do
otherdump=`echo $dump | sed "s;$dir1;$dir2;"`
diff -u $dump $otherdump
done
Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Daniel Stone <daniel@fooishbar.org>
Acked-by: Alan Coopersmith <alan.coopersmith@oracle.com>
This allows us to run the server as a normal user whilst still
being able to use the -modulepath, -logfile and -config switches
We define a xf86PrivsElevated which will do the checks and cache
the result in case it is called more than once.
Also renamed the paths #defines to match their new meaning.
Original discussion which led to this patch can be found here:
http://lists.freedesktop.org/archives/xorg-devel/2011-September/025853.html
Signed-off-by: Antoine Martin <antoine@nagafix.co.uk>
Tested-by: Michal Suchanek <hramrach at centrum.cz>
Reviewed-by: Jamey Sharp <jamey at minilop.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
If we didn't go into the if (!autoconfig) { } block, the filename,
dirname, and sysdirname pointers were never initialized, but we
freed them outside the block, leading to potential memory corruption.
Move the frees inside the block where they're initialized to avoid this.
To avoid similar problems, move the declarations of the variables that
are only used in this block inside the block.
Regression introduced by commit 3d635fe84d
Found by gcc warning:
xf86Config.c: In function 'xf86HandleConfigFile':
xf86Config.c:2303:11: warning: 'filename' may be used uninitialized in this function
xf86Config.c:2303:22: warning: 'dirname' may be used uninitialized in this function
xf86Config.c:2303:32: warning: 'sysdirname' may be used uninitialized in this function
Signed-off-by: Alan Coopersmith <alan.coopersmith@oracle.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
We call xf86penConfigDirFiles twice, so we overwrite the configDirPath
variable, losing the pointer. If we move the pointer management to the
upper layer (the function callers), they will be able to call these
functions as many times as they want, but they'll have to free those
returned values.
v2: don't leak inside XWin
4,097 bytes in 1 blocks are definitely lost in loss record 625 of 632
at 0x4C2779D: malloc (in vgpreload_memcheck-amd64-linux.so)
by 0x4D7899: DoSubstitution (scan.c:615)
by 0x4D87B0: OpenConfigDir (scan.c:845)
by 0x4D8A2D: xf86openConfigDirFiles (scan.c:955)
by 0x49031F: xf86HandleConfigFile (xf86Config.c:2327)
by 0x49A9BF: InitOutput (xf86Init.c:365)
by 0x425A7A: main (main.c:204)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
As long as we're carrying around a compatibility copy in os/strl*.c,
might as well use them.
Signed-off-by: Alan Coopersmith <alan.coopersmith@oracle.com>
Reviewed-by: Jeremy Huddleston <jeremyhu@apple.com>
Only use one init path for input devices - through NIDR.
This requires that inp_driver and inp_identifier from the
XF86ConfInputRec are copied over into the options for NIDR to see them.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
The former strdups for us. If the strdup fails we miss out on the
CorePointer option (default on anyway) and we're likely to fall over soon
anyway, so let's pretend this is the same behaviour.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Alan Coopersmith <alan.coopersmith@oracle.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
--disable-pciaccess, used together with --disable-module-int10, can be used to
disable all pci code inside the server.
Note that XSERVER_LIBPCIACCESS was previously used only in the driver side and
now it defines also whether the library is used inside the server. Also,
XORG_BUS_PCI automake variable is introduced to track PCI code needs.
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Jeremy Huddleston <jeremyhu@apple.com>
Tested-by: Jeremy Huddleston <jeremyhu@apple.com>
This does not really handle hotplug (it's handled inside the kernel,
by the 'mux' devices), but uses the wscons console driver
configuration to figure out the keyboard layout and the list of
pointing devices found by the kernel.
Signed-off-by: Matthieu Herrb <matthieu.herrb@laas.fr>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Gaetan Nadon wrote:
Alan Coopersmith wrote:
"I think we recently dropped PC98 support from the X server, so I'd
be okay with dropping the documentation now".
Let's make them be right, shall we?
Signed-off-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Jeremy Huddleston <jeremyhu@apple.com>
Acked-by: Gaetan Nadon <memsize@videotron.ca>
Acked-by: Alan Coopersmith <alan.coopersmith@oracle.com>
This reverts commit 43d9edd31e.
This commit was introduced in the 1.2 cycle when hotplugging was less than
ideal (i.e. it didn't exist). From the commit message:
Always add a mouse driver instance configured to send core events, unless
a core pointer already exists using either the mouse or void drivers. This
handles the laptop case where the config file only specifies, say,
synaptics, which causes the touchpad to work but not the pointing stick.
We don't double-instantiate the mouse driver to avoid the mouse moving twice
as fast, and we skip this logic when the user asked for a void core pointer
since that probably means they want to run with no pointer at all.
To get this case above, a user would need to disable hotplugging _and_ have a
xorg.conf that only references one device. This is possible, but not a use-case
we should worry about too much now.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Slowly merging the vastly different code-paths.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
No functional changes, just readability improvements. This also gets rid of
the count variable. Count was just used for resizing the null-terminated
list. Since we're not in a time-critical path here at all we can afford to
loop the list multiple times instead of keeping an extra variable around.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
If we find the core device, move all other device pointers forward right
then and there. The break will jump out of the top loop.
They had a special on braces today, so I added some for readability (and
fixed up tab vs space indentation.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
No functional changes.
The options we assign are the ones from the Pointer/Keyboard device so we
might as well use those readable names instead of dev[count-1]->options.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Devices are core pointers/keyboards by default now anyway, but let's set the
option to some value instead of just NULL.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
It doesn't matter. All devices are core pointer devices by default now
anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
For hotplugged devices, xf86AllocateInput does that for us but the xorg.conf
path is different. Since not all drivers reset the fd during PreInit but may
still call close(pInfo->fd) in all cases, this can terminate the logging
early.
Reproducible: add a wacom driver InputDevice section with no Option Device.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
introduced in 93ca526892.
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Nicolas Peninguy <nico@lostgeeks.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
configScreen used a dynamically allocated buffer for XF86ConfScreenRec
when conf_screen argument was NULL. This pointer was never stored
anywhere, nor was it released, so this patch makes the function use
automatically allocated storage in that situation.
[ajax: minor grammar fix]
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Rami Ylimäki <rami.ylimaki@vincit.fi>
Signed-off-by: Erkki Seppälä <erkki.seppala@vincit.fi>
Since commit b8d9c5ff removed commonOptions, we now
need to append the "Core{Keyboard,Pointer}" options to
the existing list.
Fixes passing options to devices confirured in xorg.conf
on systems where autoaddevices is false.
Signed-off-by: Matthieu Herrb <matthieu.herrb@laas.fr>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Single allocation point for input devices, most notably a single point to
reset default values.
Without this patch, the file descriptor default was -1 for hotplugged
devices and 0 for config devices. Drivers that don't overwrite the default
themselves would thus fail if configured in the xorg.conf.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Options set in the configuration file were unconditionally overwritten by
the server. Merge the already existing options and the new options together
instead of just overwriting ones.
Introduced in commit 2199842ed5
Author: Peter Hutterer <peter.hutterer@who-t.net>
Date: Thu Sep 2 10:52:54 2010 +1000
xfree86: remove extraOptions field from IDevRec.
X.Org Bug 32115 <http://bugs.freedesktop.org/show_bug.cgi?id=32115>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Tested-by: David Ronis <ronis@ronispc.chem.mcgill.ca>
That helps us get rid of:
| CC xf86Config.lo
| xf86Config.c: In function ‘T.174’:
| xf86Config.c:1228: warning: ‘Pointer$module’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$module’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$drv’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$drv’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$type_name’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$type_name’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$private’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$private’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$dev’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$dev’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$fd’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$fd’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$set_device_valuators’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$set_device_valuators’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$switch_mode’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$switch_mode’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$control_proc’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$control_proc’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$read_input’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$read_input’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$device_control’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$device_control’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$flags’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$flags’ was declared here
| xf86Config.c:1228: warning: ‘Pointer$next’ may be used uninitialized in this function
| xf86Config.c:1097: note: ‘Pointer$next’ was declared here
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
This is a more accurate name for the actual functionality than
allowEmptyInput. Historically, allowEmptyInput has allowed the server to
start with no input devices. Since 1.4 and the introduction of VCP and VCK,
there are always two input devices present.
allowEmptyInput was changed in behaviour to essentially "ignore xorg.conf
devices or not", auto-adding the built-in devices if disabled.
Rename to forceInputDevices, because that's essentially what it does. When
disabled (i.e. when hotplugging is enabled), it disables all
mouse/kbd/vmmouse devices configured in the xorg.conf file.
When enabled, it forces the traditional behaviour for input devices:
- use input devices configured in the server layout
- if none are configured, use the first pointer and the first keyboard
device in the xorg.conf
- if none are configured, create the default pointer/keyboard devices.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Julien Cristau <jcristau@debian.org>
An estimated 100% (rounded down to the nearest percent) of the people who
have this in their configuration don't actually know what this option does.
Protect the users from themselves.
IIRC, AEI on was useful for some time between 1.4 and 1.5 and never since.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
../../../../hw/xfree86/common/xf86Config.c: In function 'configDRI':
../../../../hw/xfree86/common/xf86Config.c:2213:9: warning: unused variable
'i'
Introduced in 788bfbf18a
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Matt Turner <mattst88@gmail.com>
../../../../hw/xfree86/common/xf86Config.c: In function
'fixup_video_driver_list':
../../../../hw/xfree86/common/xf86Config.c:507:19: warning: unused variable
'atimisc'
../../../../hw/xfree86/common/xf86Config.c:507:12: warning: unused variable
'ati'
Introduced in 52577ae8ee.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Matt Turner <mattst88@gmail.com>
This was only ever used from the glint driver, which has since lost its
DRI support.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
This was to distinguish XFree86 3.x files from XFree86 4.x files. It
never really made sense to be looking for xorg.conf-4.
Reviewed-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Jesse Adkins <jesserayadkins@gmail.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jesse Adkins <jesserayadkins@gmail.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
This hasn't worked since we switched to dlloader.
Reviewed-by: Jesse Adkins <jesserayadkins@gmail.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Make xf86IsolateDevice private on PCI common file.
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Mikhail Gusarov <dottedmag@dottedmag.net>
This struct is superfluous, maintaining the same info as the InputInfoRec
(with the exception of the driver name).
This is a rather large commit with the majority of changes being a rename
from the fields of the IDevRec (idev, commonOptions) to the InputInfoRec
(pInfo, options).
The actual changes affect the initialization process of the input device:
In NewInputDeviceRequest, the InputInfoRec is now always allocated and just
added to the internal list in xf86NewInputDevice() if the init process
succeeded.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
This patch was generated by the following Perl code:
perl -i -pe 's/([^_])return\s*\(\s*([^(]+?)\s*\)s*;(\s+(\n))?/$1return $2;$4/g;'
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Marcin Baczyński <marbacz@gmail.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Alan Coopersmith <alan.coopersmith@oracle.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
The only remaining X-functions used in server are XNF*, the rest is converted to
plain alloc/calloc/realloc/free/strdup.
X* functions are still exported from server and x* macros are still defined in
header file, so both ABI and API are not affected by this change.
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
This patch was created with:
git ls-files '*.[ch]' | while read f; do unifdef -B -DRENDER -o $f $f; done
Signed-off-by: Keith Packard <keithp@keithp.com>
In addition to the conf files found in /etc/X11 or $sysconfdir/X11 used
for local administration, we also reserve a system directory for vendor
and package usage. The simple search path is:
/usr/share/X11/xorg.conf.d
$datadir/X11/xorg.conf.d
Files from these directories will have the lowest config priority. The
directory $datadir/X11/xorg.conf.d is exported from xorg-server.pc in
the variable "sysconfigdir". Packages should install their .conf files
to the directory specified by:
`pkg-config --variable=sysconfigdir xorg-server`
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
There's no reason to carry all the oddities from xorg.conf like appended
hostname to the search path for xorg.conf.d. This changes it to something
very simple:
/etc/X11/<cmdline>
$sysconfdir/X11/<cmdline>
/etc/X11/xorg.conf.d
$sysconfdir/X11/xorg.conf.d
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
xf86Config.c: In function 'configInputDevices':
xf86Config.c:1514: error: request for member 'lay_identifier' in something
not a structure or union
make[5]: *** [xf86Config.lo] Error 1
Introduced with e1165632bd.
X.Org Bug 26971 <http://bugs.freedesktop.org/show_bug.cgi?id=26971>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Dan Nicholson <dbn.lists@gmail.com>
In the vast majority of cases there is no xorg.conf that specifies a core
pointer/keyboard. Skip this warning, since we'll get another notification
about how the server relies on the config backend for input devices anyway.
Leave the warning in for the error case (AEI off).
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Fernando Carrijo <fcarrijo@yahoo.com.br>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Currently the config and InputClasses are merged together so that the
options from the config backend have the highest priority. This is bad
since it means options such as a default XKB layout set by the backend
cannot be changed by the user.
This patch changes order of precedence to be:
1. xorg.conf
2. xorg.conf.d (later files have higher priority)
3. config backend
In order to allow this ordering, the config parsing has been changed to
read the xorg.conf.d files before xorg.conf. This has the consequence
that the core device picking which looks for the first InputDevice may
not find it in xorg.conf.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Add a backend using libudev for input hotplug, and disable the hal and
dbus backends if this one is enabled.
XKB configuration happens using xkb{rules,model,layout,variant,options}
properties (case-insensitive) on the device. We fill in InputAttributes
to allow configuration through InputClass in Xorg.
Requires udev 148 for the input_id helper and ID_INPUT* properties.
Signed-off-by: Julien Cristau <jcristau@debian.org>
Acked-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Any input device with this option will be automatically added to whichever
server layout is selected at startup. This removes the need to reference a
device from the ServerLayout section. The two following configuration are
identical:
CONFIG 1:
Section "ServerLayout"
InputDevice "foo"
EndSection
Section "InputDevice"
Identifier "foo"
...
EndSection
CONFIG 2:
Section "InputDevice"
Identifier "foo"
Option "AutoServerLayout" "on"
...
EndSection
The selection of the server layout affects both explicitly specified
layouts and the implicit layout.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Keith Packard <keithp at keithp.com>
Add a new command line parameter, -configdir, to specify the config
directory to be used. Rules are the same as -config for root vs. user
privileges.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer at who-t.net>
Currently there is a single file, xorg.conf, for configuring the server.
This works fine most of the time, but it becomes a problem when packages
or system services need to adjust the configuration. Instead, allow
multiple configuration files to live in a directory. Typically this will
be /etc/X11/xorg.conf.d.
Files with a suffix of .conf will be read and added to the server
configuration after xorg.conf. The server won't fall back to using the
auto configuration unless there is no config file and there are no files
in the config directory.
Right now this uses a simpler search template than the config file
search path by not using the command line or environment variable
parameters. The matching code was refactored a bit to make this more
coherent. Any DDX wanting to read the config files will need to call
xf86initConfigFiles before opening/reading them. This is to allow
xf86openConfigFile without xf86openConfigDirFiles and vice-versa.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer at who-t.net>
I don't think this one has been in use since 2003.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Default remains the same - on for most OS'es on i386 (except Solaris),
off for everyone else. Can be manually toggled via --enable-pc98 or
--disable-pc98.
Signed-off-by: Alan Coopersmith <alan.coopersmith@sun.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Technically, disabling AEI is the right suggestion. AEI off forces the
server to init the built-in defaults for input devices (or pick the first
one from the config file). At the same time, hotplugging is still available
with AEI off.
Unfortunatly, in the vast majority of cases users want to simply disable
hotplugging or have a working server while the local HAL configuration is
broken or missing. Disabling AEI will lead to duplicate events, triple
keystrokes, etc. once the configuration works again.
It's not actually required to remove AEI once hotplugging works again,
though it will in many cases lead to a setup that appears broken.
Asking users to disable AutoAddDevices instead means those users disable
hotplugging, can then fix the HAL setup and they _must_ remove the config
line again to test if hotplugging works again. Which doesn't leave them with
a broken config once everything is working nice and dandy. Less bugreports,
everybody wins.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Dan Nicholson <dbn.lists@gmail.com>
Acked-by: Daniel Stone <daniel@fooishbar.org>
Acked-by: Rémi Cardona <remi@gentoo.org>
Acked-by: James Cloos <cloos@jhcloos.com>
Boolean option to enable/disable SIGIO handlers is set by the first
of these found:
- UseSIGIO option is set in xorg.conf ServerFlags
- Default set at build time by ./configure --enable-use-sigio-by-default
- Platform default value: Solaris = no, all others = yes
This matches the current settings on all platforms except Solaris.
This reverts Solaris (for now) to the settings used in Xorg 1.6, before
SIGIO support for Solaris was added, due to some system level bugs that
won't be resolved in time for Xorg 1.7 release, but allows us to enable
when those are resolved (or when we need to test if they're resolved).
See http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6879897
Signed-off-by: Alan Coopersmith <alan.coopersmith@sun.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
49b93df8a3 made the hard dependency on
a "fixed" font go away but only Xorg could use the built-ins fonts by
default.
With this commit, all DDXs get "built-ins" appended to their FontPath, not
just Xorg.
Tested with Xorg, Xvfb and Xnest.
Signed-off-by: Rémi Cardona <remi@gentoo.org>
Signed-off-by: Jon TURNEY <jon.turney@dronecode.org.uk>
Tested-by: Jon TURNEY <jon.turney@dronecode.org.uk>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
This was a vestige from the days before we'd make the mode list from the
EDID data, and from CRT technology when you could reasonably assume that
higher refresh rates were better. Also it did not function as advertised,
acting as a high-pass filter instead of a band-pass.
Historically, if no input device was referenced in the ServerLayout,
the server would pick the first "mouse" device found in the xorg.conf.
This patch gives evdev, synaptics, vmmouse and void the same status. If
there is a section in the config file using this driver - use it as the core
pointer.
Device selection is in driver-order, not in config-order. If a "mouse"
device is listed after a "synaptics" device, the "mouse" device gets
preference. This replicates the original behaviour.
This code only takes effect if AllowEmptyInput is off and there is no core
pointer in the server layout.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Zapping is triggered by xkb these days, so note in the man page that it's the
Terminate_Server action. Since it's XKB, personal preferences towards or
against zapping should be achieved through xkb rulesets.
If Terminate_Server is not in the xkb actions, then we can't zap anyway and we
don't need a default of DontZap "on".
This patch restores the old meaning of DontZap - disallow zapping altogether,
regardless of XKB's current keymap.
Ideally, this patch should be accompanied by b0f64bdab00db652e in
xkeyboard-config.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Was only used to provide a list of input devices that XF86-Misc could use,
now that XF86-Misc is gone, was parsed and logged, then completely ignored.
(Depends on previous patch that introduces OBSOLETE_TOKEN in parser to
make obsolete keywords like InputDevices & RgbPath be non-fatal errors.)
Signed-off-by: Alan Coopersmith <alan.coopersmith@sun.com>
Acked-by: Adam Jackson <ajax@redhat.com>
Adam Jackson
Aaron Plattner
Søren Sandmann
Laércio de Sousa
Oleg Samarin
Peter Hutterer
Keith Packard
Jeremy White
Daniel Stone
Tomas Carnecky
Dave Airlie
Yaakov Selkowitz
Antoine Martin
Alan Coopersmith
Paulo Zanoni
Tiago Vignatti
Matthieu Herrb
Alexandr Shadchin
Jamey Sharp
Erkki Seppälä
Cyril Brulebois
Mikhail Gusarov
Dan Nicholson
Julien Cristau
Alan Coopersmith
Rémi Cardona
Oliver McFadden