DGA key event support was lost in commit
8da0ff2d51. Bring it back.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
After collecting the driver's default options, report the list of options
set for the device before calling PreInit(). This helps with debugging those
cases where options are not merged correctly.
xf86OptionListReport reports with verbosity 5, higher than the default
verbosity so this won't generate logspam in the default case.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Simon Thum <simon.thum@gmx.de>
If a device doesn't send valuators, don't try to move its position.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Single allocation point for input devices, most notably a single point to
reset default values.
Without this patch, the file descriptor default was -1 for hotplugged
devices and 0 for config devices. Drivers that don't overwrite the default
themselves would thus fail if configured in the xorg.conf.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Some devices should be initialised as floating from the start (e.g.
Joysticks and accelerometers benefit from this). Currently users use the
"SendCoreEvents" "off" flag for this, which isn't the most appropriate
naming.
Add an option "Floating", deprecate the others. Still parsed and handled by
the server.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
The XI2 protocol supports per-axis modes, but the server so far does
not. This change adds support in the server.
A complication is the fact that XI1 does not support per-axis modes.
The solution provided here is to set a per-device mode that defines the
mode of at least the first two valuators (X and Y). Note that initializing
the first two axes to a different mode than the device mode will fail.
For XI1 events, any axes following the first two that have the same mode
will be sent to clients, up to the first axis that has a different mode.
Thus, if a device has relative, then absolute, then relative mode axes,
only the first block of relative axes will be sent over XI1.
Since the XI2 protocol supports per-axis modes, all axes are sent to the
client.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
This commit introduces an abstraction API for handling masked valuators. The
intent is that drivers just allocate a mask, set the data and pass the mask
to the server. The actual storage type of the mask is hidden from the
drivers.
The new calls for drivers are:
valuator_mask_new() /* to allocate a valuator mask */
valuator_mask_zero() /* to reset a mask to zero */
valuator_mask_set() /* to set a valuator value */
The new interface to the server is
xf86PostMotionEventM()
xf86PostButtonEventM()
xf86PostKeyboardEventM()
xf86PostProximityEventM()
all taking a mask instead of the valuator array.
The ValuatorMask is currently defined for MAX_VALUATORS fixed size due to
memory allocation restrictions in SIGIO handlers.
For easier review, a lot of the code still uses separate valuator arrays.
This will be fixed in a later patch.
This patch was initially written by Chase Douglas.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Maybe it's just me but every time I look at it I get confused again and need
to work it out from scratch. Rename the parameters to something
self-explanatory, to/from and min/max.
No functional change.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Julien Cristau <jcristau@debian.org>
We have a driver hook - it's UnInit.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Fernando Carrijo <fcarrijo@freedesktop.org>
This struct is superfluous, maintaining the same info as the InputInfoRec
(with the exception of the driver name).
This is a rather large commit with the majority of changes being a rename
from the fields of the IDevRec (idev, commonOptions) to the InputInfoRec
(pInfo, options).
The actual changes affect the initialization process of the input device:
In NewInputDeviceRequest, the InputInfoRec is now always allocated and just
added to the internal list in xf86NewInputDevice() if the init process
succeeded.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
When no identifier for the device was specified, the allocated IDevRec (and
its associated fields) need to be freed.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Fernando Carrijo <fcarrijo@freedesktop.org>
And unexport it, drivers don't need to call this in the new init process.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
InputInfoRec hasn't had a free function pointer since the git import.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Fernando Carrijo <fcarrijo@freedesktop.org>
None of them are called by the server.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Reviewed-by: Fernando Carrijo <fcarrijo@freedesktop.org>
This field was only used in one location where we can use a local variable.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
This hook wasn't used by any DDX. Device addition and removal is handled by
the config backend, so we don't need to do anything special that during the
ListInputDevices request processing.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
In theory, these hooks were to be used for DDX-specific device enablement.
None of the DDXs however did anything here. Now we call DEVICE_INIT on all
devices when they are added, so the xfree86 DDX as the only one with real
code didn't do anything here.
kdrive checked for device validity but that's already handled in
ProcXOpenDevice.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Instead of shoving it in rather unrelated places, move acceleration init
into xf86NewInputDevice.
Caveat: It's not clear atm how relevant other callers of ActivateDevice
(like OpenDevice) actually are.
Signed-off-by: Simon Thum <simon.thum@gmx.de>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Two names pointing to the same struct for over 7 years now. Remove the
define, if drivers don't want to change they can always do the typedef
themselves.
Rename all "LocalDevicePtr local" to "InputInfoPtr pInfo".
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Make xf86AllocateInput static in the process, this function is only called
from one location.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Right now, Xephyr and others don't get to use XKB on the slave devices.
Which works given that no-one cares about SDs just yet but event processing
is different if the ProcessInputProc isn't wrapped properly.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
From the documentation:
"This is mainly to allow a touch screen to be used with netscape and other
browsers which do strange things if the mouse moves between button down and
button up."
CLOSED - NOTOURBUG
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
PreInit returns a status code. Let's use that instead of having it report
Success in some cases but not set the XI86_CONFIGURED flag and thus signal
an init failure.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
RegisterPointerDevice() and RegisterKeyboardDevice() were already mapped to
RegisterOtherDevice() and obsolete.
RegisterOtherDevice() was called for all devices and the two assignments can
simply be moved into AddInputDevice(). Purge RegisterOtherDevice() and
pretend it never happened.
*lalalalala*
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
ActivateGrab and DeactivateGrab are set in AddInputDevice() already.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
No-one but the joystick driver uses it and that one should be using NIDR
instead.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
config_info is the only reliable indicator we have in the server for
duplicate devices (drivers can test for maj/min on fds as well). Don't set
this after the device has been initialized but assume it's important enough
to set during NIDR.
This makes the option "config_info" available to the drivers as well.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
The main change introduced in this patch is the removal of the
back-and-forth between DDX and the driver.
The DDX now allocates the InputInfoRec and fills it with default values. The
DDX processes common options (and module-specific default options, if
appropriate) before passing the initialised struct to the driver.
The driver may do module-specific initializations and return Success or an
error code in the case of a failure.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
../../../../hw/xfree86/common/xf86Xinput.c: In function ‘xf86AllocateInput’:
../../../../hw/xfree86/common/xf86Xinput.c:722: warning: implicit
declaration of function ‘DuplicateModule’
../../../../hw/xfree86/common/xf86Xinput.c:722: warning: nested extern
declaration of ‘DuplicateModule’
../../../../hw/xfree86/common/xf86Xinput.c:722: warning: assignment makes
pointer from integer without a cast
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
None of them do anything useful now that pointer acceleration is
entirely handled in the server. (Does not completely nuke yet,
since that would be an API/ABI break.)
Signed-off-by: Alan Coopersmith <alan.coopersmith@oracle.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Often we want to apply a driver specific option to a set of devices and
don't care how the driver was selected for that device. The MatchDriver
entry can be used to match the current driver string:
MatchDriver "evdev|mouse"
Option "Emulate3Buttons" "yes"
The driver string is a case sensitive match.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Currently when there multiple InputClass entries of the same type, only
the last entry is used and the previous ones are ignored. Instead,
multiple entries are used to create multiple matching conditions.
For instance, an InputClass with
MatchProduct "foo"
MatchProduct "bar"
will require that the device's product name contain both foo and bar.
This provides a complement to the || style matching when an entry is
split using the "|" token.
The xorg.conf man page has added an example to hopefully clarify the two
types of compound matches.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Sometimes the vendor and product names aren't specific enough to target
a USB device, so expose the numeric codes in the ID. A MatchUSBID entry
has been added that supports shell pattern matching when fnmatch(3) is
available. For example:
MatchUSBID "046d:*"
The IDs are stored in lowercase hex separated by a ':' like "lsusb" or
"lspci -n".
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Serial input devices lack properties such as product or vendor name. This
makes matching InputClass sections difficult. Add a MatchPnPID entry to
test against the PnP ID of the device. The entry supports a shell pattern
match on platforms that support fnmatch(3). For example:
MatchPnPID "WACf*"
A match type for non-path pattern matching, match_pattern, has been added.
The difference between this and match_path_pattern is the FNM_PATHNAME
flag in fnmatch(3).
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
This patch was generated by the following Perl code:
perl -i -pe 's/([^_])return\s*\(\s*([^(]+?)\s*\)s*;(\s+(\n))?/$1return $2;$4/g;'
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Allow InputClass sections to match against the running operating system
to narrow the application of rules. An example where this could be used
is to specify that the default input driver on Linux is evdev while it's
mouse/kbd everywhere else.
The operating system name is the same as `uname -s`, and matching is
case-insensitive.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
InputClassMatches was starting to get a little hairy with all the loops
over the tokenized match strings. This adds code, but makes it easier to
read and add new matches.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Jamey Sharp <jamey at minilop.net>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
This patch has been generated by the following Coccinelle semantic patch:
@@
expression E;
@@
-if(E) { free(E); }
+free(E);
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Julien Cristau <jcristau@debian.org>
Reviewed-by: Fernando Carrijo <fcarrijo@yahoo.com.br>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Peter wants to get a larger patch sequence put together and I didn't
read past the commit message to see the 'don't take this patch
please'.
This reverts commit 531ff40301.
Some input drivers need to implement an internal hotplugging scheme for
dependent devices to provide multiple X devices off one kernel device file.
Such dependent devices can be added with NewInputDeviceRequest() but they are
not removed when the config backend calls DeleteInputDeviceRequest(),
leaving the original device to clean up.
Example of the wacom driver:
config/udev calls NewInputDeviceRequest("stylus")
wacom PreInit calls
NewInputDeviceRequest("eraser")
NewInputDeviceRequest("pad")
NewInputDeviceRequest("cursor")
PreInit finishes.
When the device is removed, the config backend only calls
DeleteInputDeviceRequest for "stylus". The driver needs to call
DeleteInputDeviceRequest for the dependent devices eraser, pad and cursor to
clean up properly.
However, when the server terminates, DeleteInputDeviceRequest is called for
all devices - the driver must not remove the dependent devices to avoid
double-frees. There is no method for the driver to detect why a device is
being removed, leading to elaborate guesswork and some amount of wishful
thinking.
Though the input driver's UnInit already supports flags, they are unused.
This patch uses the flags to supply information where the
DeleteInputDeviceRequest request originates from, allowing a driver to
selectively call DeleteInputDeviceRequest when necessary.
Also bumps XINPUT ABI.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
InputAttributes largely decide which configuration values get merged from
the xorg.conf.d snippets. While they are available in the config backend,
they are not available for any other callers of NewInputDeviceRequest().
Drivers implementing driver-side hotplugging do not have access to these
attributes and cannot have xorg.conf.d snippets specific to dependent
devices. For example, the following case cannot work right now:
Section "InputClass"
MatchProduct "Wacom"
Option "PressCurve" "0 0 100 100"
...
EndSection
Section "InputClass"
MatchProduct "Wacom"
MatchProduct "eraser"
Option "PressCurve" "10 10 50 50"
...
EndSection
The second section is not triggered, as the wacom driver cannot supply the
InputAttributes to NewInputDeviceRequest().
Add the attributes to the IDevRec and merge them into the InputInfoRec to
make them accessible in the driver. This changes the ABI for input drivers.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
attr->tags is an array of strings (null-terminated). When matching, match
against each string instead of each [i,end] substring in the first tag.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
The only remaining X-functions used in server are XNF*, the rest is converted to
plain alloc/calloc/realloc/free/strdup.
X* functions are still exported from server and x* macros are still defined in
header file, so both ABI and API are not affected by this change.
Signed-off-by: Mikhail Gusarov <dottedmag@dottedmag.net>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
We call NIDR on all devices that make it through the config backend.
Including some that have no driver assigned to them (/dev/input/mouse0 for
example). Those ones then simply get ignored by NIDR, but this should not be
noted as an error in the log file.
X_INFO is sufficient, and it may just prevent some bugreports.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Julien Cristau <jcristau@debian.org>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
High resolution devices was generating integer overflow.
For instance the wacom Cintiq 21UX has an axis value up to
87000. Thus the term (dSx * (Cx - Rxlow)) is greater than
MAX_INT32.
Using 64bits integer avoids such problem.
Signed-off-by: Philippe Ribet <ribet@cena.fr>
Signed-off-by: Benjamin Tissoires <tissoire@cena.fr>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Commit 8736d112af changed the priority
ordering of the InputClass option merging to be "last match wins". This
fixes the handling of Option "Ignore" to follow that logic.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
A driver that is assigned by an input class is only present as idev->driver.
The driver itself has no access to this information once PreInit is called.
For devices that rely on chain-hotplugging (wacom), this means that for the
second device the driver information is lost and the second device cannot be
initialized through NewInputDeviceRequest. Although this could be worked
around by hardcoding the driver name in the wacom driver, having the
assigned driver in the options seems like the better solution.
This issue only manifests itself with the udev backend. With HAL, the driver
is assigned by HAL and the option is duplicated in config/hal.c.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Currently the config and InputClasses are merged together so that the
options from the config backend have the highest priority. This is bad
since it means options such as a default XKB layout set by the backend
cannot be changed by the user.
This patch changes order of precedence to be:
1. xorg.conf
2. xorg.conf.d (later files have higher priority)
3. config backend
In order to allow this ordering, the config parsing has been changed to
read the xorg.conf.d files before xorg.conf. This has the consequence
that the core device picking which looks for the first InputDevice may
not find it in xorg.conf.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Tags may be a list of comma-separated strings that match against a MatchTag
InputClass section. If any of the tags specified for a device match against
the MatchTag of the section, this match is evaluated true and passed on to
the next match condition.
Tags are specified as "input.tags" (hal) or "ID_INPUT.tags" (udev), the
value of the tags is case-sensitive and require an exact match (not a
substring match).
i.e. "quirk" will not match "QUIRK", "need_quirk" or "quirk_needed".
Example configuration:
udev:
ENV{ID_INPUT.tags}="foo,bar"
hal:
<merge key="input.tags" type="string">foo,bar</merge>
xorg.conf:
Section "InputClass"
Identifier "foobar quirks"
MatchTag "foo|foobar"
Option "Foobar" "on"
EndSection
Where the xorg.conf section matches against any device with the tag "foo"
or tag "foobar" set.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
In order to keep the number of InputClass sections manageable, allow
matches to contain multiple arguments. The arguments will be separated
by the '|' character. This allows a policy to apply to multiple types of
devices. For example:
Section "InputClass"
Identifier "Inverted Mice"
MatchProduct "Crazy Mouse|Silly Mouse"
Option "InvertX" "yes"
EndSection
This applies to the MatchProduct, MatchVendor and MatchDevicePath
entries. Currently there is no way to escape characters, so names or
patterns cannot contain '|'.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Sometimes it is desirable to skip adding specific input devices to the
server. The "Ignore" option is used similarly to Monitor sections so
that matched devices will not be added. BadIDChoice is returned to the
config backend so that it will clean up all resources.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Drivers and options specified in InputClass sections work on a "first
match wins" strategy. Let's be consistent when documenting it.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
xf86Xinput.c relied on xkbsrv.h's definition of True/False which seems odd
at first and weird on second glance.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
With InputClass support, it makes more sense to cover all
aspects of acceleration in options. Previously, one could only set the
default on the command line.
Signed-off-by: Simon Thum <simon.thum@gmx.de>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Simon Thum <simon.thum@gmx.de>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Add a backend using libudev for input hotplug, and disable the hal and
dbus backends if this one is enabled.
XKB configuration happens using xkb{rules,model,layout,variant,options}
properties (case-insensitive) on the device. We fill in InputAttributes
to allow configuration through InputClass in Xorg.
Requires udev 148 for the input_id helper and ID_INPUT* properties.
Signed-off-by: Julien Cristau <jcristau@debian.org>
Acked-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
While the identifier is likely set before the input classes are merged, the
driver may not be. Hence don't check for a driver before we've completed
configuration for this device.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Julien Cristau <jcristau@debian.org>
Currently Xorg uses hal's fdi files to decide what configuration options
are applied to automatically added input devices. This is sub-optimal
since it requires users to use a new and different configuration store
than xorg.conf.
The InputClass section attempts to provide a system similar to hal where
configuration can be applied to all devices with certain attributes. For
now, devices can be matched to:
* A substring of the product name via a MatchProduct entry
* A substring of the vendir name via a MatchVendor entry
* A pathname pattern of the device file via a MatchDevicePath entry
* A device type via boolean entries for MatchIsKeyboard, MatchIsPointer,
MatchIsJoystick, MatchIsTablet, MatchIsTouchpad and MatchIsTouchscreen
See the INPUTCLASS section in xorg.conf(5) for more details.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
In order to give NewInputDeviceRequest more information, a new
InputAttributes type is introduced. Currently, this collects the product
and vendor name, device path, and sets booleans for attributes such as
having keys and/or a pointer. Only the HAL backend fills in the
attributes, though.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer at who-t.net>
This was initially fixed by commit 3932a84857
but then (presumably not intentionally) undone by commit
1d54479cb3 .
Signed-off-by: Hans Nieser <hnsr@xs4all.nl>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Marcin Baczyński <marbacz@gmail.com>
Reviewed-by: Jeremy Huddleston <jeremyhu@apple.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
All input drivers use xf86PostKeyEventP indirectly now and have been since
it exists. I guess that qualifies it as tested - no need to spam the logs.
Reported-by: Felix Wenk
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
The DIX event queue is allocated before InitInput is called, so fetch
the pointer there and not randomly at other times. This avoids failing
to fetch the pointer sometimes during server regen and then smashing
memory through the stale pointer from the previous server generation.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
xf86PostKeyboardEvent also makes use of xf86PostKeyEventP to avoid code
duplication, and the valuator verification has been split into the
XI_VERIFY_VALUATORS macro.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
InternalEvents shouldn't be used anywhere outside the X server itself. Split
up into events.h for opaque typedefs for the events needed by various
headers and eventstr.h for the actual struct definitions.
eventstr.h must only be included by code that requires internal events and
is not part of the SDK.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
xextproto had Xlib client headers moved into libXext.
Protocol header files are named fooproto.h, header files with constants
foo.h or fooconst.h where foo.h was already in use for client-side headers.
isMaster is not enough as long as we differ between master pointers and
keyboard. With flexible device classes, the usual checks for whether a
master device is a pointer (currently check for ->button, ->valuators or
->key) do not work as an SD may post an event through a master and mess this
check up.
Example, a device with valuators but no buttons would remove the button
class from the VCP and thus result in the
IsPointerDevice(inputInfo.pointer) == FALSE.
This will become worse in the future when new device classes are introduced
that aren't provided in the current system (e.g. a switch class).
This patch replaces isMaster with "type", one of SLAVE, MASTER_POINTER and
MASTER_KEYBOARD. All checks for dev->isMaster are replaced with an
IsMaster(dev).
This approach is broken anyway. DIPT only checked for the XInput type
"MOUSE" and the only user of this is xf86ActivateDevice when it sets the
Activate/DeactivateGrab functions.
Since synaptics and wacom set their own types, evdev only sets MOUSE for,
well, mice half the devices didn't have this set correctly anyway.
Instead, ActivatePointerGrab should be merged together with
ActivateKeyboardGrab.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
There's only two reasons for hierarchy events:
- device is added, removed, etc. In this case we want to send the event as
it happens.
- devices are added in a XIChangeDeviceHierarchy request. In this case we
only want one event cumulating all changes.
We only put internal events into the queue now, so let's check for ET_Motion
rather than the MotionNotify.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
After the call to xf86ActivateDevice, the new device will be added to
inputInfo.devices. However, if the subsequent call to ActivateDevice
fails, the correponding InputInfoRec for the device is deleted but an
entry still remains in inputInfo.devices. This might lead to a server
crash later on (on InitAndStartDevices for instance) when the device
control proc would be called for an invalid device.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Replace multi-stage filtering with simple linear velocity,
tracked several instances backwards. A heuristic ensures
only approximately linear motion is considered, so velocity
remains valid in any case. Numerical stability is much
better, and nothing changes to people who didn't tune the
advanced features of the previous algorithm.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
remove a few lines which redo part of the pointer acceleration
init. Properties is the way to go for them.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
DeleteInputDeviceRequest function doesn't handle "virtual" devices well.
TightVNC libvnc.so module to X (which makes bare Xorg VNC capable) uses such
kind of devices.
Bare Xvnc (it is something like Xvfb) simply uses AddInputDevice &
RegisterDevice functions. Xvnc uses DeleteInputDeviceRequest from Xi/stubs.c
so everything works fine (now I see that DeleteInputDeviceRequest in
Xi/stubs.c should call RemoveDevice function, shouldn't it? :) )
Situation is quite different when you use libvnc.so module. It uses same
schema as Xvnc, so it simply calls AddInputDevice & RegisterDevice. Thus
device is created correctly. When server is terminated it calls
DeleteInputDeviceRequest (now from hw/xfree86/common/xf86Xinput.c) for each
device. Here is the difference - Xvnc calls DeleteInputDeviceRequest from
Xi/stubs.c as I wrote above. Thus Xorg gets sigsegv because "VNC" devices
don't have real input driver.
X.Org Bug 20087 <http://bugs.freedesktop.org/show_bug.cgi?id=20087>
[This isn't really a fix (libVNC should behave correctly) but not crashing the
server sounds like an improvement.]
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
No more #ifdef XKB, because you can't disable the build, and no more
noXkbExtension either.
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Ville Syrjala
Peter Hutterer
Chase Douglas
Simon Thum
Alan Coopersmith
Keith Packard
Dan Nicholson
Mikhail Gusarov
Benjamin Tissoires
Julien Cristau
Hans Nieser
Marcin Baczyński
Oliver McFadden
Ander Conselvan de Oliveira
Tomas Carnecky
Adam Tkac
Maarten Maathuis
Daniel Stone