bondtech lgx lite v2

KlipperScreen.conf

@@ -9,9 +9,5 @@
 #~# [main]
 #~# screen_blanking = 300
 #~# show_heater_power = True
-#~# 
+#~# print_view = list
-#~# [graph Printer]
-#~# temperature_sensor mcu = False
-#~# heater_bed = False
-#~# extruder = False
 #~#

hardware/hardware.cfg

@@ -1,4 +1,5 @@
 [include mcu.cfg]
 [include steppers.cfg]
+[include manta.cfg]
 [include nitehawk.cfg]
-[include manta.cfg]
+#[include nh-36.cfg]

hardware/manta.cfg

@@ -10,6 +10,7 @@ sensor_pin: PB0
 min_temp: 0
 max_temp: 100
 gcode_id: chamber
+pullup_resistor: 2200
 
 #####################################################################
 # 	Bed Heater
@@ -26,13 +27,13 @@ sensor_pin: PB1
 ##  The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power"
 ##  If max_power is greater than 1.0, use 1.0
 sensor_type: Generic 3950
-max_power: 0.96
+max_power: 0.92
 min_temp: 0
-max_temp: 120
+max_temp: 125
 control: pid
-pid_kp: 62.117
+pid_kp: 56.391
-pid_ki: 3.210
+pid_ki: 1.843
-pid_kd: 300.492
+pid_kd: 431.393
 
 #####################################################################
 # 	Fan Control
@@ -54,56 +55,6 @@ target_temp: 50
 max_power: 0.5
 shutdown_speed: 0
 
-#[heater_fan hotend_fan]
-##	Hotend Fan - CNC_FAN1
-#pin: PF9
-#max_power: 1.0
-#kick_start_time: 0.5
-#heater: extruder
-#heater_temp: 50.0
-##	If you are experiencing back flow, you can reduce fan_speed
-#fan_speed: 1.0
-
-#[heater_fan controller_fan]
-##	Controller fan - CNC_FAN2
-#pin: PF6
-#kick_start_time: 0.5
-#heater: heater_bed
-#heater_temp: 45.0
-
-#[heater_fan exhaust_fan]
-##	Exhaust fan - CNC_FAN3
-#pin: PF8
-#max_power: 1.0
-#shutdown_speed: 0.0
-#kick_start_time: 5.0
-#heater: heater_bed
-#heater_temp: 60
-#fan_speed: 1.0
-
-#[heater_fan fan4]
-#pin: PA4
-
-#[heater_fan fan5]
-#pin: PA6
-#tachometer_pin: PC2
-
-#[heater_fan fan6]
-#pin: PA2
-#tachometer_pin: PC1
-
-#####################################################################
-# 	LED Control
-#####################################################################
-
-#[output_pin caselight]
-# Chamber Lighting - HE2 Connector (Optional)
-#pin: PA3
-#pwm:true
-#shutdown_value: 0
-#value:1
-#cycle_time: 0.01
-
 #####################################################################
 # 	Homing and Gantry Adjustment Routines
 #####################################################################
@@ -122,7 +73,6 @@ z_hop:10
 gantry_corners:
 	-60,-10
 	410,420
-#	Probe points
 points:
 	50,25
 	50,275
@@ -130,10 +80,10 @@ points:
 	300,25
 
 #--------------------------------------------------------------------
-speed: 250
+speed: 600
 horizontal_move_z: 10
 retries: 5
-retry_tolerance: 0.0075
+retry_tolerance: 0.025
 max_adjust: 10
 
 [board_pins]
@@ -152,30 +102,6 @@ aliases:
     EXP2_7=PE8, EXP2_8=<RST>,
     EXP2_9=<GND>, EXP2_10=<NC>
 
-# See the sample-lcd.cfg file for definitions of common LCD displays.
-
-#####################################################################
-# 	Displays
-#####################################################################
-
-## 	Uncomment the display that you have
-#--------------------------------------------------------------------
-
-#[display]
-##	RepRapDiscount 128x64 Full Graphic Smart Controller
-#lcd_type: st7920
-#cs_pin: EXP1_4
-#sclk_pin: EXP1_5
-#sid_pin: EXP1_3
-#menu_timeout: 40
-#encoder_pins: ^EXP2_5, ^EXP2_3
-#click_pin: ^!EXP1_2
-
-#[output_pin beeper]
-#pin: EXP1_1
-
-#--------------------------------------------------------------------
-
 
 #####################################################################
 # 	Macros

hardware/nh-36.cfg

@@ -0,0 +1,14 @@
+
+[mcu nhk]
+##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
+##--------------------------------------------------------------------
+serial: 4E473531310A2450
+restart_method: command
+
+#####################################################################
+# 	Probe
+#####################################################################
+## Probe Port
+[probe]
+pin: nhk:gpio10
+z_offset: -0.890

hardware/nitehawk.cfg

@@ -17,10 +17,14 @@
 [mcu nhk]
 ##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
 ##--------------------------------------------------------------------
-serial: /dev/serial/by-id/usb-Klipper_rp2040_313436333211C87C-if00
+serial: /dev/serial/by-id/usb-Klipper_rp2040_4E473531310A2450-if00
 restart_method: command
 ##--------------------------------------------------------------------
 
+[temperature_sensor nhk]
+sensor_type: temperature_mcu
+sensor_mcu: nhk
+
 #####################################################################
 # 	Extruder
 #####################################################################
@@ -30,17 +34,16 @@ dir_pin: !nhk:gpio24
 enable_pin: !nhk:gpio25
 heater_pin: nhk:gpio9
 sensor_pin: nhk:gpio29
-sensor_type: PT1000
+sensor_type: Generic 3950
 pullup_resistor: 2200
 min_temp: 0
-max_temp: 400
+max_temp: 450
 microsteps: 16
 control: pid
-pid_kp: 13.942
+pid_kp: 12.655
-pid_ki: 0.596
+pid_ki: 0.524
-pid_kd: 81.561
+pid_kd: 76.404
-rotation_distance: 22.6789511   #Bondtech 5mm Drive Gears
+rotation_distance: 5.7
-gear_ratio: 50:10
 filament_diameter: 1.75
 nozzle_diameter: 0.4
 max_extrude_cross_section: 5
@@ -50,7 +53,7 @@ sense_resistor: 0.100
 uart_pin: nhk:gpio0
 tx_pin: nhk:gpio1
 interpolate: false
-run_current: 0.8
+run_current: 0.65
 
 #####################################################################
 #   Fans
@@ -60,8 +63,8 @@ run_current: 0.8
 pin: nhk:gpio6
 #tachometer_pin: nhk:gpio17
 #tachometer_ppr: 2
-
 ## HEF
+
 [heater_fan hotend_fan]
 pin: nhk:gpio5
 #tachometer_pin: nhk:gpio16
@@ -90,7 +93,7 @@ pin: !nhk:gpio8
 #   Accelerometer
 #####################################################################
 [adxl345]
-cs_pin: nhk:gpio21
+cs_pin: nhk:gpio27
 spi_software_sclk_pin: nhk:gpio18
 spi_software_mosi_pin: nhk:gpio20
 spi_software_miso_pin: nhk:gpio19
@@ -113,19 +116,19 @@ probe_points:
 #max_temp: 100
 #gcode_id: chamber_th
 
-[thermistor CMFB103F3950FANT]
+# [thermistor CMFB103F3950FANT]
-temperature1: 0.0
+# temperature1: 0.0
-resistance1: 32116.0
+# resistance1: 32116.0
-temperature2: 40.0
+# temperature2: 40.0
-resistance2: 5309.0
+# resistance2: 5309.0
-temperature3: 80.0
+# temperature3: 80.0
-resistance3: 1228.0
+# resistance3: 1228.0
 
-[temperature_sensor nh_temp]
+# [temperature_sensor nh_temp]
-## Nitehawk PCB Sensor
+# ## Nitehawk PCB Sensor
-sensor_type: CMFB103F3950FANT
+# sensor_type: CMFB103F3950FANT
-sensor_pin: nhk:gpio26
+# sensor_pin: nhk:gpio26
-pullup_resistor: 2200
+# pullup_resistor: 2200
-min_temp: 0
+# min_temp: 0
-max_temp: 100
+# max_temp: 100
-gcode_id: nh_th
+# gcode_id: nh_th

printer-20240901_090049.cfg

@@ -0,0 +1,40 @@
+#[include print_area_bed_mesh.cfg]
+[include mainsail.cfg]
+[include hardware/hardware.cfg]
+[include misc/misc.cfg]
+[include macros/macros.cfg]
+[include config/config.cfg]
+[include KAMP_Settings.cfg]
+
+[printer]
+max_velocity: 600
+max_accel: 6500
+kinematics: corexy
+max_z_velocity: 30 			#Max 15 for 12V TMC Drivers, can increase for 24V
+max_z_accel: 350
+square_corner_velocity: 5.0
+
+[exclude_object]
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.129938, 0.077438, 0.072438, 0.064938, 0.079938, 0.084938, 0.092438
+#*# 	  0.074938, 0.042438, 0.032438, 0.029938, 0.032438, 0.059938, 0.079938
+#*# 	  0.024938, 0.012438, -0.015062, -0.007562, -0.000062, 0.022438, 0.032438
+#*# 	  0.014938, -0.000062, -0.015062, -0.020062, 0.007438, 0.027438, 0.047438
+#*# 	  0.044938, 0.029938, -0.012562, -0.002562, 0.009938, 0.024938, 0.039938
+#*# 	  0.089938, 0.049938, 0.012438, 0.019938, 0.029938, 0.032438, 0.064938
+#*# 	  0.152438, 0.109938, 0.074938, 0.069938, 0.069938, 0.069938, 0.079938
+#*# x_count = 7
+#*# y_count = 7
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = bicubic
+#*# tension = 0.2
+#*# min_x = 20.0
+#*# max_x = 320.0
+#*# min_y = 20.0
+#*# max_y = 320.0